Airlink101 AWLL3026 Instrukcja Użytkownika Strona 1

802.11g USB 2.0 Adapter Model # AWLL3026 User’s Manual Ver. 1A

10 3. Configuring USB Adapter as a Wireless Client The USB adapter can be set to either Station or Access Point Mode from the Mode drop-down menu. St

11 Step 1 Select the SSID of your wireless router/access point from the Available Network list and click on the Connect this site button. Step 2 V

12 Current Network Information: Displays the network information of the wireless router/access point that the USB adapter is currently connected to

13 3.1 Configuring General Settings Click Change to configure the adapter’s General Connection Setting. Channel: This setting is for Access Point

14 3.2 Configuring Encryption Security Click WEP Encryption Key Setting to configure the WEP settings. Click Change to configure the WEP Key Sett

15 Key Value: Enter the applicable key values. Up to four key values may be entered. Note the following rules when entering Key values: ‧ 64-bit ke

16 1. Select TKIP for Encryption, WPA PSK for Authentication Mode, and click Apply. 2. Click on WPA Encryption Setting and click Change. 3. Ente

17 3.3 Configuring Profile After you have configured all the settings, you can save your settings as a profile so you don’t have to re-configure

18 3.4 Advanced Settings Click on Advanced Setting from the More Setting window to configure the adapter’s advanced settings. User Interface: sel

19 3.5 Information Click on Information from the More Setting window to view the driver and utility’s information.

2 Table of Contents 1. INTRODUCTION ... 4 1.1 Featur

20 4. Configuring USB Adapter as an Access Point 4.1 Configuring Access Point You can configure the USB Adapter as an access point for other wireles

21 Click on Change to configure the settings. Channel: select the channel you want to use. Basic Rate: select the applicable transfer rate. Tx

22 4.2 Configuring Encryption Security Select Enable from the WEP drop-down menu and click Setting. Key Length: Select the appropriate encryption

23 4.3 Configuring MAC Address Filter Filter Type: Disable: disables MAC address filter. Accept: only accepts connection from the MAC address li

24 5. Appendix 5.1 Specifications Electrical Specifications Interface USB 2.0 Standard, USB 1.1 Compliant Standards Conformance IEEE 802.11 / 802.11

25 5.2 Troubleshooting A. If the utility cannot be opened or it reports that the adapter is not found, uninstall the driver and utility and try ins

26 For Windows 98SE/ME Step 1 Go to Start, Run, type winipcfg and click OK. Step 2 Select the adapter from the drop-down menu and click Release. S

27 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Theo

3 Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FC

4 1. Introduction The 802.11g USB 2.0 Adapter (hereafter called USB adapter), compliant with IEEE 802.11b/g, is a high-efficiency wireless adapter fo

5 2. Installation Procedures 2.1 Install Utility Software Note: Before installing the utility software, DO NOT insert the USB adapter into your com

6 Step 3 Click Next at the welcome screen. Step 4 Click Next to accept the default destination location for the driver to be installed in or cl

7 Step 5 For Windows XP, click Continue Anyway at the Windows Logo Compatibility screen. For Windows 2000, click Yes at the Digital Signature s

8 2.2 Install Driver Note: In most cases, Windows will automatically install the driver after the computer is restarted. If the Found New Hardware

9 For Windows 2000, click Yes at the Digital Signature screen. For Windows 98SE or ME, insert the Windows 98SE or ME CD if prompted to do so and